Cal. No. U68*
Refine your searchU68*
All Reset
Resetting the watch - All Reset
When the watch does not work properly, you can reset all the settings.
If the power reserve is insufficient, charge the watch first.
The setting values after All Reset
| Time of the analog indication | 0:00:00AM |
|---|---|
| Time of the digital indication | 0:00:00AM, 12-hour basis |
| Calendar of the digital indication | January 1, 2008, Tuesday |
| World time | Time zone: “UTC” for both the analog and digital indications |
| Show/hide setting of areas: “SET” for all areas | |
| Time zone setting for “HOM”: “---” (no setting) | |
| Summer time | “OF” (OFF) for all zones |
| Automatic summer time switching function: On “SMT AU (AUTO)” | |
| Chronograph | Reset (0 hour 0 minutes 0 seconds 00) |
| Alarm | “OF” (OFF) for both “AL-1” and “AL-2” |
| Alarm time: 12:0 on both “AL-1” and “AL-2” | |
| Time zone for alarm time: “UTC” for both “AL-1” and “AL-2” | |
| Timer | Reset (99 minutes 0 seconds) |
| Automatic reception setting | “AUT” (AUTO) |
Resetting the watch - All Reset
- Pull the crown out to position 1.
- Rotate the crown to set the mode hand to [CHR].
- Pull the crown out to position 2.
- Press and release the upper right button B and the lower right button A at the same time.
- Checking the reference position
- Press and hold the upper right button B for 2 seconds or more.
- Press and release the upper right button B repeatedly to change the target to be corrected.
- Adjust the reference position of the hands.
- After finishing the adjustment, press and hold the upper right button B for 2 seconds or more.
- Push the crown in to position 0.
- Pull the crown out to position 1.
- Rotate the crown to set the mode hand to [TME] or [CAL].
- Push the crown in to position 0 to finish the procedure.
An area name and “(M)” appear alternately on the digital indication (L).
!
Turn the crown so that the mode hand will point to the center of the mode name securely.
The hands move to their current reference position.
!
Proceed to the next step after the hands stopped.
All Reset is executed and all segments of the digital indicataion are turned on.
Check the reference position of the hands after their back-and-forth movement stopped.
!
After the hands stopped, check whether they are at correct positions referring to the figure below.
The reference position must be corrected if any one of the positions is incorrect.
Correct reference positions
Hour, minute and second hands: 0 hour 0 minute 0 second
24-hour hand: “24” (straight above)
UTC indication: 0 hour 0 minute
Power reserve indication hand: “CHN”
| Correct | No adjustment is required. Push the crown in to position 0 to finish the procedure. Change the mode of the watch to [TME] or [CAL]. |
|---|---|
| Wrong | Click here to proceed below. |
“CHA” appears on the digital indication (L) and the power reserve indication hand becomes adjustable.
!
Each time you press the upper right button B, the target changes as follows:
Power reserve indication hand -> UTC indication -> hour and 24-hour hands → minute hand → (back to the top)
!
The target to be corrected is indicated on the digital indication (L).
| Adjustment target | Digital indication (L) | Operation |
|---|---|---|
| Power reserve indication hand | CHA | Rotate the crown to set it to “CHN”. |
| UTC indication | UTC | Rotate the crown to set it 0:00. Pressing the lower right button A moves the minute hand away to show the UTC indication without obstruction. Press the button again to return the hand to normal. |
| Hour and 24-hour hands | HR | Rotate the crown to set the hour hand to 0:00 and the 24-hour hand to “24” (straight above). Pressing the lower right button A moves the minute hand away to show the hour hand without obstruction. Press the button again to return the hand to normal. |
| Minute hand | MIN | Rotate the crown to set it 0 minutes. |
!
If you rotate the crown quickly a few times, the hand will move continuously.
To stop the rapid movement, rotate the crown in either direction.
!
You cannot adjust the reference position of the second hand.
“(0)” appears on the digital indication (L) and adjustment of the reference position is finished.
The watch returns to normal indication.
!
Change the mode of the watch to [TME] or [CAL] following the steps below.
An area name and “(M)” appear alternately on the digital indication (L).
!
Turn the crown so that the mode hand will point to the center of the mode name securely.
After that, execute world time setting and adjustment of time and calendar.